[法规草案] 智利电力和燃料监管局 (SEC) 发布了燃料产品安全测试认证协议草案 (PC) No. 65/3:2026 - 燃气式户外红外线庭院取暖器。此认证协议依据 CSA/ANSI Z83.26:2020 – CSA 2.37:2020 标准，制定了使用气体燃料的户外红外线辐射取暖的认证程序。此外，该协议涵盖的产品必须符合 SEC 豁免决议第 745:2004 号或其任何替代条款。这意味着该设备必须配备内置软管和调节器进行销售。

The Superintendency of Electricity and Fuels (SEC) of Chile has announced draft Safety Test Protocol for Safety Testing Fuel Products (PC) No. 65/3:2026 - Gas-fired outdoor infra-red patio heaters.

This protocol establishes the certification procedure for outdoor infrared radiant heaters using gaseous fuels, in accordance with CSA/ANSI Z83.26:2020 – CSA 2.37:2020.

Additionally, products covered by this protocol must comply with SEC Exempt Resolution No. 745:2004, or any provision that replaces it. This means that the appliance must be marketed with an incorporated hose and regulator.

2026年7月7日，印度电信工程中心 (TEC) 发布一则公众咨询，就Wi-Fi接入点设备通用要求修订案 (TEC 38020: 2026) 征求公众意见。修订要点如下：

- 新增Wi-Fi 6GHz频段和Wi-Fi 7标准，以及相关参数和技术特性要求；

- 规定若设备已通过Wi-Fi联盟认证，则已测试参数可豁免TEC认证测试；

- 要求设备应符合适用的通信设备安全保障要求 (ITSAR) 要求；

- 更新引用的安全标准和EMC标准至最新版本。

On July 7, 2026, the Telecom Engineering Centre (TEC) of India issued a public consultation seeking public input on the amendment to the General Requirements for Wi-Fi Access Point Equipment (TEC 38020: 2026). The key points of the revision are as follows:

- Added Wi-Fi 6GHz band and Wi-Fi 7 standards, along with related parameters and technical requirements;

- It is stipulated that if the device has passed Wi-Fi Alliance certification, the tested parameters can be exempted from TEC certification testing;

- Require the device to meet the applicable Communication Equipment Security Assurance Requirements (ITSAR) requirements;

- Updated cited safety standards and EMC standards to the latest versions.

[法规草案] 印度电信工程中心 (TEC) 发布了电信设备强制性测试与认证 (MTCTE) 制度下路由器基本要求 (ER) 的修订草案。

India’s Telecommunication Engineering Centre (TEC) has released draft revisedEssential Requirements (ER) for Routers under the Mandatory Testing and Certification of Telecom Equipment (MTCTE) regime. This updated draft expands current standards and is open for stakeholder comments.

印度发布2026年5.9 GHz 频段车联网 (Cellular V2X) 车载单元免执照规则，允许符合规定的 Cellular V2X (C-V2X) 车载设备，在印度 5.9 GHz 频段免申请无线电执照即可使用。需注意法规免除的是无线电执照 (Radio Licence)，但设备型式核准 (Equipment Type Approval) 仍然需要。

India published "Use of On Board Unit for Cellular Vehicle-to-Everything Communication in the 5.9 GHz band (Exemption from Licensing Requirements) Rules, 2026". This rule allows compliant Cellular V2X (C-V2X) vehicle-mounted devices to operate in the 5.9 GHz band in India without a radio license. It should be noted that the regulation exempts the user from a radio license, but equipment type approval is still required.

印度发布G.S.R. 468(E): 2026 年 77–81 GHz 频段短程汽车雷达系统免执照规则，将 77–81 GHz 车用短距离雷达 (Short-Range Automotive Radar，SRARS) 列为免无线电执照 (Licence Exempt) 的设备。也就是说，符合技术条件的车用雷达，不需要另外申请调频执照即可在印度使用。需注意法规免除的是无线电执照 (Radio Licence)，但设备型式核准 (Equipment Type Approval) 仍然需要。

India published "G.S.R. 468(E): Use of Short-Range Automotive Radar System in the 77–81 GHz band (Exemption from Licensing Requirements) Rules, 2026". The rule classifies 77–81 GHz Short-Range Automotive Radar (SRARS) as license-exempt equipment. This means that compliant automotive radar can be used in India without requiring a separate radio frequency license. It should be noted that the regulation exempts the user from a radio license, but equipment type approval is still required.

Meity于2026年7月26日再次公告IS 18112:2022 (Digital Television Receiver for Satellite Broadcast Transmission) 的强制执行日 (Implementation Date) 自2026/07/27延至2027/01/26。

IS 18112:2022 实施日期的延期历史：

-2025-04-26（原始公告)

-第一次延至 2025-10-26

-第二次延至 2026-01-26

-第三次延至 2026-07-26

-最新延至2027-01-26

请注意TV产品(IS 62368 or IS 616) 并须同时符合IS 18112方能符合CRS注册.

Meity issued another notice on July 26, 2026, postponing the implementation date of IS 18112:2022 (Digital Television Receiver for Satellite Broadcast Transmission) from July 27, 2026 to January 26, 2027.

History of IS 18112:2022 implementation date postponements:

-Original notice: April 26, 2025

-First postponement: October 26, 2025

-Second postponement: January 26, 2026

-Third postponement: July 26, 2026

- Latest postponement: January 26, 2027

Please note that TV products (IS 62368 or IS 616) must also comply with IS 18112 to be eligible for CRS registration.

BIS 进一步厘清 CRS 产品由 IS 13252 (Part 1):2010／IS 616:2017 迁移至 IS/IEC 62368-1:2023 的实务要求，包括既有 License 的升版程序、Migration 申请方式及过渡期间的安排。FAQ 亦鼓励制造商尽早启动转换，并说明零部件 (Components) 与终端产品 (End Products) 可平行进行测试与认证，以缩短整体认证时程，降低过渡期截止前实验室及审查资源壅塞的风险。

BIS clarified about the migration to IS/IEC 62368-1:2023, providing further clarification on the migration requirements for CRS products from IS 13252 (Part 1):2010 and IS 616:2017 to IS/IEC 62368-1:2023. The guidelines cover the upgrade process for existing BIS licenses, migration application procedures, and transitional arrangements. They also encourage manufacturers to initiate the migration as early as possible and confirm that components and end products may undergo testing and certification in parallel, helping to shorten overall certification timelines and reduce the risk of laboratory and certification bottlenecks before the transition deadline.

[法规草案] 经济产业省 (METI) 提议对《电器设备及材料技术要求部令》的解释公告进行部分修订。

此次修订旨在更新日本电器设备及材料技术要求部令的解释，将附录表2、3和5合并为附录表12，同时修订附录表12以反映最新的国际标准，包括IEC标准和最新的JIS版本。

The Ministry of Economy, Trade and Industry (METI) has proposed a partial revision to the Notice on the Interpretation of the Ministerial Ordinance Specifying Technical Requirements for Electrical Appliances and Materials.

The proposed revision updates the interpretation of Japan’s ministerial ordinance on technical requirements for electrical appliances and materials by consolidating Appendix 2, 3, and 5 into Appendix 12, while also revising Appendix 12 to reflect the latest international standards, including IEC standards and the most recent corresponding JIS versions.

黎巴嫩 TRA 目前针对汽车零部件提供为期一年的过渡期。在过渡期间，相关产品进口无需申请 TRA 型式认证证书。然而，TRA 仍建议汽车零部件制造商及汽车制造商善用此过渡期，提前申请 TRA 证书，以利过渡期结束后顺利符合相关要求。

The Lebanon TRA has introduced a one-year transition period for automotive components, during which a TRA Type Approval Certificate is not required for importation. Nevertheless, the TRA encourages automotive component manufacturers and vehicle manufacturers to apply for the certificate during the transition period to ensure compliance once the exemption expires.

马来西亚通信与多媒体委员会 (MCMC) 发布了《MCMC MTSFB TC T007:2026 Short Range Devices (SRD)》(第三次修订) 以及《MCMC MTSFB TC T022:2026 Communication Equipment – Baseline Requirements》(通信设备 基本要求)。

MCMC MTSFB TC T007:2026 的主要更新如下：

•安全、电磁兼容性 (EMC)、产品标识及电源等基线要求已移至 MCMC MTSFB TC T022:2026；

•新增 6 GHz SRD/RLAN (5925–6425 MHz)频段；

•新增适用于公路及铁路应用的超宽带 (UWB) 设备要求，并纳入 8500–10600 MHz UWB 运行规定；

•重新调整 5 GHz WLAN/RLAN 频段划分，并新增室内及室外使用的发射功率限制；

•采用 ETSI EN 303 687 及 EN 303 883 标准；

•移除原 UWB 部分中 3400–3700 MHz 的频段配置；

•13.553–13.567 MHz 频段新增 500 mW EIRP 发射功率类别。

MCMC MTSFB TC T022:2026《Communication Equipment – Baseline Requirements》

规范架构调整

•2020版：T007同时涵盖射频 (RF) 要求及产品标识、电气安全、电磁兼容性 (EMC) 等通用基线要求。

•2026版：将通用基线要求独立整合至新增的 MCMC MTSFB TC T022:2026，T007则聚焦于SRD产品的射频技术要求。

•适用原则：T007主要规定射频参数；产品标识、电气安全、EMC、SAR、功率密度及其他适用的通用要求，则依据产品类别适用T022中的相关规定。

The Malaysian Communications and Multimedia Commission (MCMC) has published the third revision of MCMC MTSFB TC T007:2026 – Short Range Devices (SRD) and introduced MCMC MTSFB TC T022:2026 – Communication Equipment – Baseline Requirements.

Key changes in MCMC MTSFB TC T007:2026

•Baseline requirements covering electrical safety, electromagnetic compatibility (EMC), product marking, and power supply have been relocated to MCMC MTSFB TC T022:2026.

•Introduces the 6 GHz SRD/RLAN frequency band (5925–6425 MHz).

•Adds requirements for Ultra-Wideband (UWB) road and rail applications, including operation in the 8500–10600 MHz frequency range.

•Revises the 5 GHz WLAN/RLAN frequency allocations and introduces separate indoor and outdoor transmit power limits.

•Adopts ETSI EN 303 687 and ETSI EN 303 883 as applicable technical standards.

•Removes the 3400–3700 MHz UWB frequency allocation included in previous editions.

•Introduces a new 500 mW EIRP category for operation in the 13.553–13.567 MHz frequency band.

MCMC MTSFB TC T022:2026 – Communication Equipment – Baseline Requirements

Regulatory Framework Restructuring

•2020 Framework: MCMC MTSFB TC T007 included both RF technical requirements and general baseline requirements, such as product marking, electrical safety, and electromagnetic compatibility (EMC).

•2026 Framework: The general baseline requirements have been consolidated into the newly established MCMC MTSFB TC T022:2026 – Communication Equipment – Baseline Requirements, while MCMC MTSFB TC T007:2026 is now focused exclusively on RF technical requirements for Short Range Devices (SRDs).

•Compliance approach: T007 specifies the applicable RF technical requirements, whereas product marking, electrical safety, EMC, Specific Absorption Rate (SAR), power density, and other applicable baseline requirements are addressed in T022, depending on the product category.

2026年7月15日，马来西亚通信与多媒体委员会 (MCMC) 通过技术标准论坛 (MTSFB) 就新的物联网功能安全、网络安全及隐私管理标准征求意见。主要内容如下：

•新的技术标准将替代现有的MCMC MTSFB TC G013:2018；

•马来西亚现有的物联网安全标准包括：应用安全MCMC MTSFB TC G031、设备安全MCMC MTSFB TC G031、隐私要求MCMC MTSFB TC G031及功能安全MCMC MTSFB TC G031，这些标准被新的标准草案引用。由于新标准引用上述标准中内容，因此技术及合规难度大为提升；

•标准要求功能安全、网络安全、隐私管控贯穿设备全生命周期：厂商必须长期提供签名OTA固件更新、漏洞响应机制、持续安全监控、故障溯源日志留存。

On July 15, 2026, the Malaysian Communications and Multimedia Council (MCMC) solicited feedback on new IoT functional safety, cybersecurity, and privacy management standards through the Technical Standards Forum Bhd (MTSFB). The main contents are as follows:

•The new technical standard will replace the existing MCMC MTSFB TC G013:2018;

•Malaysia's existing IoT security standards include: Application Security MCMC MTSFB TC G031, Device Security MCMC MTSFB TC G031, Privacy Requirements MCMC MTSFB TC G031, and Functional Safety MCMC MTSFB TC G031. These standards are referenced in the new draft standards. Because the new standard references content from the above standards, the technical and compliance difficulties have greatly increased;

•The standard requires functional safety, network security, and privacy controls throughout the entire device lifecycle: vendors must provide long-term signed OTA firmware updates, vulnerability response mechanisms, continuous security monitoring, and fault traceability log retention.

墨西哥经济部 (SE) 于 2026 年 5 月 29 日发布修正《对外贸易一般规则及标准》，内容包括以下更新：

- 智能型手机及其他移动电话 (HS 编码 8517.13.01、8517.14.91 及 8517.18.99) 不再适用简化进口合规豁免。其后，SE 透过 SNICE 公告确认，相关产品自 2026 年 7 月 1 日 起，进口时须证明符合适用的 NOM 标准，包括 NOM-001-SCFI-2018 及 NOM-024-SCFI-2013。

- SE 将启用新的 PLATIICA（Plataforma Tecnológica Integral de Infraestructura de la Calidad） 平台，用于管理标准化、计量、符合性评定、市场监督、验证，以及相关信息、服务与行政程序。

本协议已于 2026 年 5 月 30 日生效；惟上述手机产品的 NOM 合规要求自 2026 年 7 月 1 日起开始适用。

On 29 May 2026, Mexico's Secretariat of Economy (SE) published amendments to the General Rules and Criteria on Foreign Trade, introducing the following updates:

- Smartphones and other mobile phones classified under HS Codes 8517.13.01, 8517.14.91, and 8517.18.99 are no longer eligible for the simplified import compliance exemption. Subsequently, SNICE confirmed that, effective 1 July 2026, these products must demonstrate compliance with the applicable NOM standards, including NOM-001-SCFI-2018 and NOM-024-SCFI-2013, when imported into Mexico.

- SE will implement a new platform, PLATIICA (Plataforma Tecnológica Integral de Infraestructura de la Calidad), to manage information, services, procedures, and activities related to standardization, metrology, conformity assessment, market surveillance, and verification.

The amendments entered into force on 30 May 2026; however, the NOM compliance requirements for the above-mentioned mobile phone products become applicable on 1 July 2026.

韩国国家无线电研究机构 (RRA) 于2026年7月24日通知广播与电信设备合格评定通知第2026-4号， 修订内容主要将《电信事业用无线设备技术标准》附则的修订内容<5G NR 行动通信无线设备> 1) 陆地行动台（Land Mobile Station）之收发设备、2) 基地台之收发设备及中继设备、3) 其他相关设备纳入《广播通信器材等适合性评价公告》。该通知自公告之日起生效。

On July 24, 2026, the Korea National Radio Research Agency (RRA) issued Notice No. 2026-4, amending the Notice on Conformity Assessment of Broadcasting and Telecommunications Equipment. The primary revision reflects the amendments to the supplementary provisions of the Technical Standards for Radio Equipment for Telecommunications Services, incorporating the scope of 5G NR mobile communication radio equipment into the Conformity Assessment Notice, including:

1) Transmitting and receiving equipment for Land Mobile Stations;

2) Transmitting and receiving equipment and repeater equipment for Base 3) Stations; and Other related equipment.        This notification takes effect on the date of its publication.

汤加无线通讯设备形式认可 (Type Approval) 主管机关已由 Ministry of Communications (MIC) 移交至新成立的 Communications Commission Tonga (CCT)。自 2026 年 7 月 1 日起，所有新的 Type Approval 申请均由 CCT 负责受理。 MIC 已核发的 Type Approval 证书原则上持续有效；后续的新申请、变更或续证案件应向 CCT 办理。

The responsibility for wireless equipment Type Approval in Tonga has been transferred from the Ministry of Communications (MIC) to the newly established Communications Commission Tonga (CCT). Starting 1 July 2026, all new Type Approval applications are processed by CCT. Type Approval certificates issued previously by MIC are generally expected to remain valid. Future applications, amendments, or renewals should be submitted to CCT.

越南发布第48/2026/TT-BCA号通知，发布新的国家技术法规《QCVN 11:2026/BCA——互联网协议 (IP) 网络摄像机基本网络安全要求》。该法规取代现行《QCVN 135:2024/BTTTT》，并自2026年7月1日起正式生效。

Vietnam publishes Circular No. 48/2026/TT-BCA on QCVN 11:2026/BCA on technical regulation for Surveillance Camera using Internet Protocol - Baseline cybersecurity requirements. It replaces current regulation QCVN 135:2024/BTTTT and is effective from 01 July 2026.

[法规草案] 越南科技部 (MST) 拟发布第二版/修订版通知草案，该草案规定由科技部负责管理的中高风险产品和商品列表，并根据越南进出口商品清单列出了相应的HS编码、国家技术标准、产品描述和质量管理要求。

Vietnam proposes second/revised draft Circular stipulates the List of products and goods with medium  and  high  risk  levels  under  the  management  responsibility  of  the  Ministry  of Science and Technology, along with the corresponding HS codes in accordance with the Vietnamese  Export  and  Import  Goods  List,  corresponding  national  technical  standards, product descriptions, and corresponding quality management requirements.

The draft is expected to replace Circular No. 29/2025/TT-BKHCN.

[法规草案] 中国发布《家用空调能效等级和能效最低允许值国家标准 (草案)》。该文件规定了家用空调的能效等级、能效最低允许值、测试方法和实施要求。该文件适用于额定制冷量不超过14000W的空气冷却冷凝器、全封闭式电动压缩机、T1型气候型家用空调以及额定制热量不超过14000W的低温空气源热泵家用空调；不适用于移动式空调、多联式空调 (热泵)、风管式空调 (热泵) 和厨房空调。

China published draft National  Standard  of  Minimum  allowable  values  of  the  energy efficiency and energy efficiency grades for room air conditioners.

This  document  specifies  energy  efficiency  grades，minimum allowable values of energy efficiency, testing methods and implementation requirements for room air conditioners.

This document applies to room air conditioners with air cooling condensers, fully enclosed electric compressors, rated cooling capacity of not exceeding 14000W, T1 climate type and low ambient temperature air source heat pump air heaters with a nominal heating capacity of not more than 14000W.

This document does not apply to mobile air conditioners, multi-split air conditioning (heat pump) units, ducted air conditioning (heat pump) units and kitchen air conditioners.

韩国技术标准院 (KATS) 于2026年7月20日发布配合有关电器用品安全管理的国际协议 (WTO/TBT、IECEE) 修订7项适用之电器用品安全标准: KC 60335-2-2、KC 60335-2-12、KC 60335-2-30、KC 60335-2-32、KC 60081、KC 60969、KC 61347-2-3. 该通知自公告之日起生效，惟原安全标准得并行适用至2027年7月20日 (即公告施行满一年) 为止。

On July 20, 2026, the Korea Agency for Technology and Standards (KATS) announced revisions to seven applicable Korean electrical appliance safety standards in accordance with international agreements on electrical appliance safety management (WTO/TBT and IECEE). The revised standards are:

KC 60335-2-2、KC 60335-2-12、KC 60335-2-30、KC 60335-2-32

KC 60081；KC 60969、KC 61347-2-3

This notification takes effect on the date of its publication.

However, the previous safety standards may continue to be applied concurrently until July 20, 2027, i.e., for one year from the effective date of this notification.

[法规草案] 澳洲气候变迁、能源、环境和水资源部 (DCCEEW) 发布了《水效率标签和标准 (WELS) 计划 - 2025-26 年产品扩展计划工作计划》，概述了 WELS 在未来一年的新产品研究重点、其当前发展阶段和未来工作计划。

Australia Department of Climate Change, Energy, the Environment and Water (DCCEEW) published "Water Efficiency Labelling and Standards (WELS) Scheme – Product Expansion Program 2025–26 Work Plan", outlining WELS's priorities for new product research in the coming year, their current stage of development, and future work plans.

[法规草案] 在2026年5月8日举行的能源与气候变化部长级理事会 (ECMC) 会议之后，温室气体和能源最低标准 (GEMS) 计划正在推进针对功率不超过65千瓦的电机、泳池水泵和空调的新要求。

这些受监管产品的新规定草案预计将于2026-2027年期间发布。

New requirements for motors, pool pumps and air conditioners up to 65kW are moving forward under the Greenhouse and Energy Minimum Standards (GEMS) program after the recent Energy and Climate Change Ministerial Council (ECMC) meeting on 8 May 2026.

Drafts of new determinations for these regulated products are supposed to be released during 2026-27.

[法规草案] 澳洲气候变迁、能源、环境和水资源部 (DCCEEW) 与能源效率和节能管理局 (EECA) 合作，正在推出一个全新的数字化平台，旨在革新澳洲和新西兰用户与能源效率法规互动的方式。

新的能源评级 RECAP (监管、执法和合规管理平台) 将取代现有的能源评级产品注册系统，并改善注册、合规和监管活动的管理方式。

The Department of Climate Change, Energy, the Environment and Water (DCCEEW), with the Energy Efficiency and Conservation Authority (EECA), is introducing a new digital platform to modernise how users interact with energy efficiency regulations across Australia and New Zealand.

The new Energy Rating RECAP (Regulatory, Enforcement and Compliance Administration Platform) will replace the current Energy Rating Product Registration system and improve how registration, compliance, and regulatory activities are managed.

2026年6月25日，哥伦比亚矿业和能源部 (Ministerio de Minas y Energía) 正式发布 Resolución 40285 de 2026《RETIQ技术标签法规》。新法规将于 2026年12月26日 强制实施，并新增电视机和电烤箱纳入监管范围，同时更新空调、冰箱、洗衣机及热水器等产品的能效等级、测试方法和标签要求。

On 25 June 2026, Colombia's Ministry of Mines and Energy published Resolution 40285 of 2026 (RETIQ Technical Regulation on Energy Labeling). The regulation will become mandatory on 26 December 2026 and expands its scope to include televisions and electric ovens, while updating efficiency classifications, testing methods, and labeling requirements for air conditioners, refrigerators, washing machines, and water heaters.

约旦标准与计量组织 (JSMO) 于2026年6月10日发布第11834号通告，在约旦更新本国技术法规之前，扩大暂时接受欧盟新版能效标签的范围。适用范围不再限于最初的6类产品，而是扩大到所有受能效标签管控的节能电器（所有适用能效标签计划的节能设备/家用电器）。

此临时措施旨在便利贸易，直至约旦本地相关技术法规正式更新并实施为止。

The Jordanian Standards and Metrology Organization (JSMO) issued Notification No. 11834 on June 10, 2026, expanding the scope of temporary acceptance of the new EU energy labeling scheme pending the update of Jordan's national technical regulations. The scope is no longer limited to the initial six product categories, but extended to all energy-efficient appliances subject to energy labeling (all energy-efficient equipment/household appliances applicable to the energy labeling scheme).

由乌兹别克斯坦标准研究院与电气工业领域标准化技术委员会联合制定的 O‘zMSt 682:2025《Maishiy va boshqa energiya iste’mol qiluvchi qurilmalarning energiya samaradorligini tamg‘alashga umumiy talablar》 已于 2026年6月1日正式生效。该标准取代原 O‘z DSt 3017:2015《家用及其他耗能设备能效标识通用要求》，为乌兹别克斯坦CUz能效标签体系建立新的技术基础，并进一步推动当地能效管理制度与国际要求接轨。

O‘zMSt 682:2025 "General Requirements for Energy Efficiency Labeling of Household and Other Energy-Consuming Devices", jointly developed by the Uzbekistan Scientific Research Institute for Standardization and the Technical Committee for Standardization in the Electrical Industry, entered into force on 1 June 2026. The new standard replaces O‘z DSt 3017:2015, establishing an updated technical framework for Uzbekistan's CUz energy labeling system and supporting closer alignment with international energy efficiency practices.

中国强制性国家标准 GB 31241.4-2026《电子电器用锂离子电池和电池组安全 第4部分：玩具》将于2027年4月1日起实施。

GB 31241.4-2026 并不是 GB 31241-2022 的修订版，而是 GB 31241 系列新增的第 4 部分 (Part 4)，专门针对玩具使用的锂离子电池与电池组订定安全要求，而 GB 31241-2022 仍主要适用于便携式电子产品使用的锂电池。

Safety of lithium ion cells and batteries used in electronic and electrical equipment—Part 4: Toys, will enter into force from 01 April, 2027.

GB 31241.4-2026 is not a revision of GB 31241-2022, but rather a new Part 4 in the GB 31241 series, which specifically sets safety requirements for lithium ion cells and batteries used in toys. GB 31241-2022, on the other hand, mainly applies to lithium batteries used in portable electronic products.

经济部标准检验局 (BSMI) 预告修正「应施检验电源供应设备类之二次锂行动电源等商品之相关检验规定」，扩大纳管范围至二次锂电池充电盒、行动式车辆启动电源、二次锂单电池、电池组/系统及道路车辆非动力用二次锂电池组等产品，并更新检验标准、检验方式及RoHS标示要求。修正内容导入CNS 62133-2、CNS 62619等新版安全标准，部分既有VPC证书及型式试验报告可透过差异测试转换，以提升锂电池产品安全及完善管理制度。

强制日期：

二次锂行动电源(项次1): 2027年7月1日。

新增纳管商品 (项次2~6) 及二次锂电池相关商品新检验方式 (项次7~9) : 2028年1月1日。

The Bureau of Standards, Metrology and Inspection (BSMI), under the Ministry of Economic Affairs (MOEA), in view of the widespread use and higher risk associated with commodities containing lithium ion cells and batteries, and in order to enhance product safety and protect consumers’ rights and interests, the Bureau of Standards, Metrology and Inspection (BSMI) proposes to revise the inspection requirements for 9 types of listed electronic products, including secondary lithium power banks and other power supply equipment. The principal amendments include expanding the inspection scope of batteries to cover secondary lithium cell blocks, battery packs, modules or systems; adopting updated versions of the applicable inspection standards; and introducing factory inspection as part of the conformity assessment procedures.

为严格强制性产品认证监管，国家认监委现修订发布《强制性产品认证实施规则 电动自行车 (试行)》(CNCA-C11-16：2026)、《强制性产品认证实施规则 童车类产品 (试行)》(CNCA-C22-01：2026)、《强制性产品认证实施规则 玩具 (试行)》(CNCA-C22-02：2026)。

自本公告发布之日至2026年10月31日，认证机构可根据认证委托人意愿，按照旧版实施规则或者新版实施规则开展CCC认证活动；2026年11月1日起，应当按照新版实施规则开展CCC认证活动。已经颁发的有效强制性产品认证证书可继续使用，认证证书转换工作采取产品变更、到期换证等自然过渡的方式完成。

To strictly regulate mandatory product certification, the Certification and Accreditation Administration of the People's Republic of China (CNCA) has revised and issued the following regulations:

-Implementation Rules for Compulsory Product Certification: Electric Bicycles (Trial) (CNCA-C11-16:2026)

-Implementation Rules for Compulsory Product Certification: Children's Vehicles (Trial) (CNCA-C22-01:2026)

-Implementation Rules for Compulsory Product Certification: Toys (Trial) (CNCA-C22-02:2026).

From the date of this announcement until October 31, 2026, certification bodies may conduct CCC certification activities according to the old or new implementation rules, based on the wishes of the certification clients. From November 1, 2026, CCC certification activities must be conducted according to the new implementation rules. Valid mandatory product certification certificates already issued may continue to be used. Certificate conversion will be completed through a natural transition process, such as product change or renewal upon expiration.

[法规草案] 经济部标准检验(BSMI) 预告修正电源供应设备类商品检验规定，涵盖电动机车、电动自行车及电动辅助自行车用非车载型充电器、电动机车充电/ 换电系统，以及电动车交流、直流与复合式充电设备。修正重点包括新增{型式认可逐批检验」双轨机制、扩大直流/复合式充电设备检验容量至750kW、导入CNS 16272信息安全标准作为连网设备检测依据，并调整货品分类号列及RoHS标示要求，以提升充电设备安全性及符合产业发展需求。

强制日期：

电动机车、自行车充电器及充电/换电系统: 2027年7月1日。

电动车交流充电设备 (≤30kW) 及直流/复合式充电设备 (≤30kW): 2026年7月1日。

电动车直流/复合式充电设备 (>30kW至750kW): 2028年1月1日。

The Bureau of Standards, Metrology and Inspection (BSMI), under the Ministry of Economic Affairs (MOEA), in view of the rising risk of international incidents involving electric motorcycles, electric bicycles, and electrically power-assisted bicycles, the Bureau of Standards, Metrology and Inspection (BSMI) proposes to expand the scope of legal inspection requirements for seven  types of power supply equipment, including non-vehicle-mounted chargers for electric motorcycles.

The proposed amendments primarily make available an alternative conformity assessment procedure for business operators to choose from. In addition, the scope of mandatory inspection for electric vehicle conductive DC/combo charging equipment is expanded from products not exceeding 30 kW to products not exceeding 750 kW.

墨西哥经济部 (Secretaría de Economía) 修改《对外贸易一般规则与标准》(Reglas y Criterios de Carácter General en Materia de Comercio Exterior) 的 NOM 附件 (Anexo 2.4.1，又称 Anexo de NOM)，将近期发布的新版 NOM-ENER 纳入进口管制。

符合这些标准的产品在进入墨西哥之前必须持有相应的合格证书，以确保其符合最新的技术规范、测试方法和商业信息要求。

在过渡期内，根据先前标准颁发的有效证书将继续有效，直至其失效。

- NOM-004-ENER-2025：用于清洁水泵送的电机泵组和电机泵。

- NOM-011-ENER-2025：中央空调、整体式空调或分体式空调。

- NOM-014-ENER-2025：单相交流电动机。

- NOM-016-ENER-2025：三相交流电动机。

Mexico's Ministry of Economy has amended Annex 2.4.1 (also known as Anexo de NOM) of the General Rules and Standards for Foreign Trade (Reglas y Criterios de Carácter General en Materia de Comercio Exterior), incorporating the recently released new version of NOM-ENER into import controls.

Products conforming to these standards must hold the corresponding certificates of conformity before entering Mexico to ensure compliance with the latest technical specifications, testing methods, and commercial information requirements.

During the transition period, valid certificates issued under previous standards will remain valid until they expire.

- NOM-004-ENER-2025: Motorized pump sets and motorized pumps for pumping clean water.

- NOM-011-ENER-2025: Central air conditioning, packaged air conditioning, or split-type air conditioning.

- NOM-014-ENER-2025: Single-phase AC motors.

- NOM-016-ENER-2025: Three-phase AC motor.

On June 25, 2026, DPIIT issued the "Transition Facilitation (Quality Control) Order, 2026," a significant transitional policy for the 10 mandatory Quality Control Orders (QCOs) under Scheme I (ISI mark).

This order provides a "transitional pathway" for certain products already subject to mandatory QCOs, allowing eligible manufacturers/suppliers to obtain specific licenses, subject to stringent assessments and compliance requirements, to support the establishment and transition of their supply chains within India.

This order does not completely replace existing QCOs, but applies only to the 10 product categories listed in the annex:

[法规草案] 菲律宾贸工部发布了《太阳能系统 (包括光伏组件、逆变器、电池储能系统、快速关闭装置、电池充电控制器和光伏电缆) 强制性产品认证技术法规》草案。

该部门行政命令旨在确保拟在菲律宾进口、制造、分销、销售、安装或使用的太阳能系统组件 (包括光伏组件、逆变器、电池储能系统、快速关断装置、电池充电控制器和光伏电缆) 符合适用的菲律宾国家标准 (PNS) 规定的安全和质量要求。一旦实施，相关产品必须符合强制性标准并获得强制性认证。

Philippines DTI Department published draft Administrative Order "Technical Regulation for the Mandatory Product Certification of Solar Energy Systems, including Solar Photovoltaic (PV) Modules, Inverters,  Battery  Energy  Storage  Systems  (BESS),  Rapid  Shutdown  Devices,  Battery Charge Controllers, and Photovoltaic (PV) Cables

This  Department  Administrative  Order  (DAO)  aims  to  ensure that  components  of  solar  energy  systems,  including  solar  photovoltaic  (PV)  modules, inverters, battery energy storage systems (BESS), rapid shutdown devices, battery charge controllers,   and   photovoltaic   (PV)   cables   intended   for   importation,   manufacture, distribution, sale, installation, or use in the Philippines, comply with prescribed safety and quality  requirements  in  accordance  with  applicable  Philippine  National  Standards  (PNS). This is to safeguard consumers, ensure product reliability, and promote the adoption of safe and efficient solar energy technologies in the country. Once implemented, the products are required to comply with mandatory standards and obtain mandatory certificate.

The draft regulation recieves comments till Jul-25 of 2026.

越南工业贸易部发布第31/2026/TT-BCT号通知，对高风险产品及货物可追溯性进行规范。

该通知要求贸易商/进口商在越南工业贸易部监管的高风险产品入口网站 (https://www.verigoods.vn/) 上注册产品标识，以确保可追溯性。

该通知自2026年7月1日起实施，过渡期至2026年12月31日结束。

高风险产品列表可参考Circular No. 33/2026/TT-BCT: 公布工业贸易部管理之中风险及高风险产品与货物列表。

Vietnam Publishes Circular No. 31/2026/TT-BCT Regulations on product and goods traceability under the management of the Ministry of Industry and Trade.

It requires the trader/importer to register the product identification for the high risk products regulated by Ministry of Industry and Trade to ensure traceability at web portal: https://www.verigoods.vn/.

It implements on Jul-1 of 2026 and transition period ends on Dec-31 of 2026.

The list of high-risk products can be found in Circular No. 33/2026/TT-BCT: List of Medium-Risk and High-Risk Products and Goods Managed by the Ministry of Industry and Trade.